Well few weeks ago India’s second biggest Direct To Home Operator, Sun Direct faced big issue after Glitch in ISRO’s satellite Insat 4B which led to switching off 50 per cent of the transponders on board the satellite and since then Sun Direct service interrupt but after 1 month, Sun Direct finally resume full service from MeaSat 3 where they will transmit their channels with Reliance BIG TV and Reliance BIG TV will share Free To Air Channels and DD Channels along with Sun Direct!

Here is complete Realignment Procedure Details for Sun Direct and Sun Direct HD viewers and now they will enjoy all channels in next few days!

Sun Direct Realignment Process

Please put Home TP: 12316 H 30000

COSHIP (5202 & 5203):

1. Step 1: Go to Installation menu and select “Advanced Installation” option.
2. Step 2: Select “Insat 4B/SAT “and press OK on the remote & press Yellow color key to “TP Edit”. (Must to be select satellite No.1)
3. Step 3: Press Right Navigation key on the remote for adding “New Parameters”
4. Step 4: Enter “New Parameters” like “Frequency, Symbol rate, Polarity”
5. Step 5: Fill all “New Parameters” and select OK “Signal strength & Quality “displayed on screen.
6. Step 6: Press Red color key to “Searching” all available channels.
7. Step 7: After Scanning Press Exit and watch our New channels on “New Satellite”

Home cast (5202 & 5203):

1. Step 1: Go to Menu and select “Installation” option.
2. Step 2: Select “Manual Scan” and press OK on
   the remote.
3. Step 3: Pop up window display on the screen “Enter PIN
   Code” default password is “0000”
4. Step 4: “Manual Scan setting” menu option below

Dish – Don’t change
Frequency (MHz) – Need Change
Polarity – Need Change
Symbol rate (Msym/s) – Need Change
Modulation – Don’t change
Pilot – Don’t change
Code Rate – Don’t change
Scan Mode – Don’t change
Service Type – Don’t change
Network Search – Don’t change

5. Step 5: Enter the all “New downlink parameters” using Numeric key on the remote.
6. Step 6: In this Menu see the “Signal Status” and “Signal Strength” levels.
7. Step 7: Press “OK” key on the remote for “Search” all channels
8. Step 8: After scanning its shows “Do you want to save changes” select “Yes” and press Exit.

Note: After satellite Migration don’t do Factory default, if customer did kindly follow the same Manual
Tuning steps again.

OPENTEC:

1. Step 1: Go to Menu and select “Installation” option.
2. Step 2: Select “Edit TP” and press OK on the remote.
3. Step 3: Press Green color key on the remote for adding “New TP”
4. Step 4: “New TP” pop up window display on the screen with “Frequency, Symbol rate, Polarity, FEC”
5. Step 5: Fill all “New Parameters” and select OK “Signal strength & Quality “displayed on top.
6. Step 6: Press Red color key on the remote for “Searching”
7. Step 7: After Scanning Press Exit and watch our New channels on “New Satellite”

Samsung (P1, P2, P3 & G2):

1. Step 1: Go to Menu and select “Advanced Actions” option and press OK.
2. Step 2: Select “Home Transponder Setting” and press OK on the remote.
3. Step 3: Pop up window display on the screen “Enter PIN Code” default password is “0000”
4. Step 4: “Home Transponder setting” menu option below

Network ID – Don’t change
Frequency (MHz) – Need Change
Symbol rate (Msym/s) – Need Change
LO Low (MHz) – Don’t change
LO High (MHz) – Don’t change
LNB Power – Don’t change
Polarization – Need Change
Position – Don’t change

5. Step 5: Enter the all “New downlink parameters” using Numeric key on the remote.
6. Step 6: Press OK to see the “Signal Status” for new parameters and press exit twice.
7. Step 7: Select “Channel Installation” and its shows “Enter PIN Code” default password is “0000”
8. Step 8: In this Menu see the “Signal Status” and “Signal Strength” and selected Parameters details.
9. Step 9: Press “Red color” key on the remote for “Search”
10. Step 10:After scanning its shows “Do you want to save” select “Yes” and press Exit.

Samsung HD:

1. Step 1: Go to Menu and select “System” option.
2. Step 2: Select “Sun Direct TV Manual Scanning” and press “OK” Key on the remote
3. Step 3: “Sun Direct TV Manual Scanning” menu option Listed below

Tuner	Don’t change
Satellite	Don’t change
Transponder	Don’t change
Frequency	Need Change
Symbol rate	Need Change
FEC	Need Change
Polarity	Need Change
Modulation	Don’t change

4. Step 4: Fill all “New Parameters” and Its shows “Signal status “displayed on same screen.
5. Step 5: Fill all “New Parameters” and Its shows “Signal status “displayed on same screen.
6. Step 6: After Scanning its shows “ Search result windows” and press “OK” to confirm.
7. Step 7: Press “Exit” and watch our New channels on “New Satellite”.

So enjoy Sun Direct Viewing now and do change according to your STB model.

About the author

Shaswat Patel wrote 650 articles on this blog.

• Blog

Popularity: 5% [?]

Related Posts

• Ten Cricket Added On Videocon D2H And Other DTH Players
• Diwali Special Offers From Indian DTHs
• Reliance BIG TV Added 7 New Channels Including DD Sports HD
• Reliance BIG TV Added 13 New Channels Including Nat Geo Music,Nat Geo Wild And Nat Geo Adventure
• How To Watch FTA Channels Through C-Band Dish Part-2: Adding More Satellites
• How To Watch FTA Channels Through C-Band Dish
• Reliance BIG TV announces 3 New Packages
• HD-DTH Buzzing In India-Be Ready For High-Definition Viewing
• Reliance BIG TV Going to Introduce 6 New Interactive Services
• Reliance BIG TV HD DVR Review And Features

Tagged as: BIG TV, DTH, Reliance BIG TV, Sun Direct, Sun Direct HD